Condensation forms when moist air touches a surface colder than its dew point. In a humid place like Lafayette, the fix is planned before the building goes up: the right insulation with a sealed, low-perm facing on the correct side, plus ventilation, all worked out for your building and how you will use it.
Get a free metal building quote
About 30 seconds: ZIP, job type, name and phone. One independent local contractor follows up. Free, no obligation.
Why metal buildings sweat
The Metal Building Manufacturers Association (MBMA) describes condensation simply: when air cools below its dew point, it can no longer hold all of its moisture, and the extra water comes out on the coldest surface it touches. Relative humidity is how close the air is to that point. At 100% relative humidity the dew point equals the air temperature, so the more humid the air, the less a surface has to cool before it gets wet.
Bare steel roof and wall panels change temperature quickly. When warm, humid air inside a shop, garage or barn meets a panel that has cooled, for example overnight or when cold rain hits the roof, water can form on the underside and drip. Lafayette's air is humid for much of the year, which is why owners here often ask about a "sweating" roof even though the area rarely sees the long cold spells MBMA links to the worst condensation problems.
Two kinds of condensation
- Visible condensation forms on surfaces you can see: the underside of panels, windows, door frames, skylights, cold water pipes and cooling ducts.
- Concealed condensation happens when moist air gets into the insulation or wall cavity and condenses on a cold surface inside it. MBMA calls this the hardest kind to deal with and potentially the most damaging. Signs it lists include damp spots, stains, mold or mildew on walls or ceilings, peeling paint and damp insulation.
The three tools: insulation, vapor retarder, ventilation
Insulation keeps the inside surfaces warmer than the dew point of the air around them. The National Insulation Association (NIA) says the insulation must be thick enough to keep the surface of its facing above the dew point of the inside air.
A vapor retarder, usually the facing laminated to metal building insulation, slows moist air on its way into the insulation. Facings are rated in perms, measured under the ASTM E96 test; the lower the perm rating, the less moisture gets through. For buildings where high humidity is likely, NIA says a facing of 0.02 or 0.09 perm is recommended. It lists white polypropylene or vinyl films with scrim reinforcing, backed by kraft paper, polyester film or foil, as the most common facings.
Ventilation lowers the amount of moisture in the air inside. MBMA recommends properly designed ventilation and says venting the wall and roof cavities can add more control.
Which side does the vapor retarder go on?
The rule both MBMA and NIA give is to put the vapor retarder on the warm side of the insulation. In most of the United States that is the inside face. NIA adds that in warmer, humid climates the warm side may be the outside, and that the architect or engineer on the project should decide in that case. That matters in Lafayette: a shop that is air-conditioned for much of the year is cooler inside than out, while an open, unconditioned barn behaves differently. Tell your contractor how the building will be used before the insulation is ordered, and ask who decides the facing type and side.
Seal the seams
A facing only works if moist air can't go around it. NIA says seams, joints and penetrations should be sealed. Ask how the installer will tape facing seams, and how they will seal around pipes, conduit, vents and door and window framing.
New slabs add moisture
MBMA notes that pouring concrete inside a building that is already erected needs special care, because a new slab releases moisture. If your slab will be poured after the frame goes up, ask your contractor how the building will be dried out and ventilated before insulation is closed in. See slabs and site prep.
Moisture you add yourself
How you use the building changes the moisture load. A shop with a propane or kerosene heater without a vent, a wash bay, livestock, a wet floor or doors left open on a muggy evening puts more water into the air. MBMA's advice to keep the moisture content of the inside air down through ventilation applies here: if you plan any of these, say so in your quote request.
Already dripping? Questions for a contractor
- Is the water coming from condensation or from a roof leak at a fastener, seam or flashing? They look alike from below.
- Is there insulation under the roof, and is its facing torn, unsealed or missing at the seams?
- Is the insulation damp? MBMA says damp or water-soaked insulation may need to be replaced or added to.
- Does the building have any ventilation, and does the use inside (heaters, washing, animals) add moisture?
- If a new roof is going over an old one, where will the insulation go? MBMA says insulation added in a retrofit should go at the existing roof level where possible, with an adequately ventilated space, because trapped warm air can condense on the cold metal roof.
What to put in a quote request
Say what the building is for, whether it will be air-conditioned or heated, whether the slab is poured before or after erection, and that you want condensation control in the quote. Ask the contractor to list the insulation thickness, the facing type and perm rating, how seams will be sealed, and what ventilation is included, so you can compare quotes line by line. We don't publish prices, because they depend on the building. Our 8 checks before you hire and kit buying guide cover the rest, and the Lafayette permit guide explains what LCG needs before you build.
This guide is general information from the industry sources listed below, not engineering advice. Your building's designer or engineer decides the insulation and vapor retarder for your project.
General information only, not legal or engineering advice. Rules change, so confirm with the agency linked below or a licensed professional before you start work.
Sources
- Metal Building Manufacturers Association: Condensation fact sheet (PDF)
- National Insulation Association: Metal building design and vapor retarders
Last reviewed: October 2026.
Related: Metal shops & garages · Barns & ag buildings · Commercial steel buildings · All guides